支管轴压下高强钢圆管X形节点的承载力计算公式
作者:
作者单位:

1.同济大学 土木工程防灾国家重点实验室,上海 200092;2.上海中侨职业技术大学 建筑工程学院,上海 201514

作者简介:

宁 鹏,博士生,主要研究方向为钢结构。E-mail:ningpeng96@tongji.edu.cn

通讯作者:

朱小利,教授级高级工程师,工学硕士,主要研究方向为钢结构。 E-mail:279732487@qq.com

中图分类号:

TU392.3

基金项目:

国家自然科学基金(51778457)


Bearing Capacity Formula of High-strength Steel CHS X-joints Under Axial Compression
Author:
Affiliation:

1.State Key Laboratory of Disaster Reduction in Civil Engineering, Tongji University, Shanghai 200092, China;2.School of Architecture and Engineering, Shanghai Zhongqiao Vocational and Technical University, Shanghai 201514, China

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    研究了支管受压的Q460、Q690、Q960高强钢圆管X形节点的静力性能。采用经试验数据验证的有限元模型进行节点有限元参数分析,研究高强钢牌号、支管与主管外径之比(β)、主管外径与其管壁厚度之比(2γ)、主管轴向应力比(n)对节点性能的影响;与有限元参数分析和文献中试验结果对比,评价我国钢结构设计标准计算公式的适用性。结果表明,节点发生主管塑性破坏,节点承载力多由主管局部变形限值(3%主管外径)确定;多数情况下钢结构设计标准计算公式高估了高强钢圆管X形节点的承载力;主管受到压力或较大拉力时均会降低节点承载力。最后,针对不同钢材牌号的圆管X形节点给出了建议的2γ范围。基于主管塑性破坏,提出了考虑高强钢屈服强度、主管拉压效应的圆管X形节点承载力计算公式。

    Abstract:

    The static performance of circular hollow section (CHS) X-joints using Q460, Q690, Q960 high-strength steel under axial compression was investigated. Using the finite element (FE) model verified by experimental results, extensive FE parametric analyses of joints were carried out. The effects of high-strength steel grades, brace-to-chord diameter ratios (β), chord diameter-to-wall thickness ratios (2γ), and chord axial stress ratios (n) on the structural behavior of joints were studied. Then, the suitability of the bearing capacity formula adopted by Chinese Standard GB 50017―2017 was evaluated against the results obtained from FE parametric analyses and literature test results. The conclusions can be drawn that the failure mode of joints is chord plastification, and the joint bearing capacity is often determined by the chord indentation limit, i.e., 3% of chord diameter; the bearing capacities of high-strength steel CHS X-joints are overestimated by the formula of Chinese Standard GB 50017―2017 in most cases; the chord subjected to pressure or larger tensile forces will reduce the joint bearing capacity. Finally, the ranges of 2γ for different steel grades are recommended. Based on the plastic failure of the chord, the bearing capacity formula of CHS X-joints is proposed, considering the yield strengths of high-strength steel and the chord preload effect.

    参考文献
    相似文献
    引证文献
引用本文

宁鹏,童乐为,朱小利.支管轴压下高强钢圆管X形节点的承载力计算公式[J].同济大学学报(自然科学版),2024,52(1):49~58

复制
分享
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:2022-11-22
  • 最后修改日期:
  • 录用日期:
  • 在线发布日期: 2024-01-27
  • 出版日期: